Slim contemporary design.
	Separate power and flow/temperature controls for ease of use.

Gradual, delayed turn off - safer showering for next user and low limescale build up.

Indicator lights: ''STANDBY', 'OVERHEAT' and 'LOW FLOW' - (indicating possible water supply fault or the need to clean the handset.) and 3 indicator lights denoting High, Medium and Low Power.

Shower will cut out if temperature becomes too hot.

Mira Response fittings with adjustable handset - lime scale resistant and easy clean.

Brass inlet connector with integral earth bonding.

Mira Sport 7.5, 9.0 and 10.8
240V AC 10.8kW, 240V AC 9.0kW, and 240v 7.5kW heaters with a Mira response Adjustable Spray handset with three different spray actions (Start, Soothe and Force). Individual lights indicate, ''STANDBY', 'OVERHEAT' and 'LOW FLOW'. Supplied complete with hose, clamp bracket, soap dish, slide bar and hose retaining ring/gel hook.

Limitations of Use

	The appliance must not be used for applications where an outlet flow control forms part of the shower fitting.
	The appliance must not be used for applications where it may become submerged in water.

 

	A water treatment device is recommended in areas where the temporary hardness is above 200ppm.
	The product and its components are only suitable for normal water supplies and should be cleaned only with mild washing up detergent or soap solution. Light golden colour products should be cleaned using a soft damp cloth only.

Application
The Mira Sport is suitable for installation as part of the following plumbing systems:
Mains cold water pressure
(gravity fed supply - use Mira Elite)
Finish
White
White/chrome
White/light golden

 

	All Mira electric showers are designed to stabilise temperature changes caused by water pressure fluctuations. These can result from taps being turned on or off or toilets flushed. Under such conditions, average shower temperatures will be held within a 6ºC band, provided that the minimum required pressure is maintained.
	The design of the most popular electric showers does not allow for thermostatic control of the showering temperature, and as such they are unable to react to changes in temperature caused by a change in mains voltage, or in the incoming water temperature. For thermostatically controlled electric showers, refer to Mira Advance.
	The temperature of incoming water will vary between summer and winter, and therefore, the temperature control knob will need to be adjusted to take account of these seasonal conditions. The length of dead leg of the cold pipe or its proximity to hot pipes, may affect the showering temperature.

 

If the water temperature reaches an unsafe level, the thermal switch assembly turns off the elements. As the water temperature falls the elements will be turned on. The switch will cycle on/off/on if the flow-rate is not increased, and the shower temperature reduced. The "OVERHEAT" neon on the Sport 10.8 will provide a visual indication of this condition

Pressure

Minimum maintained pressure: 1.0 bar

Minimum static pressure: 0.2 bar (to keep solenoid valve closed)

Maximum static pressure: 10 bar

Plumbing

	Surface mounted unit.
	Inlet connection: 15mm brass inlet compression connector which swivels to accept plumbing supplies from the top, bottom or back
	Outlet connection: ½" BSP male.
	Maximum ambient temperature for the appliance whilst in use is 30ºC

Electrical

	The appliance must be earthed.
	The appliance is intended for connection to fixed electrical wiring.
	The appliance requires a 45 Amp supply fuse.
	The terminal block will not accept cable larger than 16mm2

 

	The appliance will provide satisfactory performance with an incoming electricity supply voltage of 230V 10%. The supply voltage will affect the flow rate.
	The installation must comply with BS7671 'Requirements for Electrical Installations'. Commonly referred to as the IEE Wiring Regulations, or any particular regulations and practices, specified by the local electricity supply company.
	A separate permanently connected supply must be taken from the consumer unit to the appliance, via a double-pole switch, with at least a 3mm contact separation. The switch can be a ceiling mounted pull-cord switch within the bathroom, or a wall mounted switch in an adjacent room.
	We recommend the inclusion of a 30mA residual current device (RCD). This may be part of the consumer unit or a separate unit.

Maintenance

	Maintenance should be carried out in accordance with the information published in the Installation, Operation & Maintenance Guide, supplied with each product. This guide should be retained by the user for future reference.
	A conveniently situated isolating valve must be fitted in the supply pipework to allow complete maintenance of the product.

Approvals

	Designed to comply with relevant harmonised European Standards.
	Mira sport is BEAB approved product.
	Year 2000 compliant

Accessories

Optional DCV-H; outlet double check valve for high pressure applications, providing an alternative method of complying with Bye-law 17.

Guarantee

	Guaranteed for one year from purchase against faulty materials or workmanship.
	Optional extended warranty available. Contact Mira Customer Support.

Supporting information

Mira Sport Installation, Operation and Maintenance Guide P3279 is available prior to purchase. Contact Mira Customer Support. - 01242 262 888